|
Cables, Adapter Cards
A network card, network adapter, LAN Adapter or NIC (network interface card) is a piece of computer hardware designed to allow computers to communicate over a computer network. more...
 Home
Apple, Macintosh Computers
Desktop & Laptop Accessories
 Adapters, Chargers for...
Barcode Scanners
Batteries for Laptops
Cables, Adapter Cards
 Adapters
Audio
DVI
Extension
Firewire
 Cable
Combo (USB) Cards
PCI Controller Cards
IDE
Keyboard, Mouse
KVM, Switchbox
Other
Power
RAID
Round
SCSI
Serial
Serial ATA, SATA
Switch Box
USB 1.0
USB 2.0
Other
PCI Cards
Printer, Scanner, A-B
USB Hubs
VGA & SVGA
Cables, Connectors for...
Card Readers
Cases, Bags for Laptops
Docking Stations for Laptops
Gamepads, Joypads
Headphones, Headsets
Hubs
Infrared, IrDA
Joysticks
Keyboards
Laptop Memory Card Readers
LED Lites
Mice, Mouse
Microphones
Mounts, Auto Mounts
Other Accessories
PC Case, Tower for...
PC Remote Controls
PCMCIA Cards for Laptops
Power Supplies for...
Repair, Service Manuals
Security for Laptops
Speakers
Tablets
Trackballs
Video & Multimedia...
Video Conferencing
Webcams
Wholesale Lots
Desktop & Laptop Components
Desktop PCs
Drives, Controllers &...
Laptops, Notebooks
Monitors & Projectors
It is both an OSI layer 1 (physical layer) and layer 2 (data link layer) device, as it provides physical access to a networking medium and provides a low-level addressing system through the use of MAC addresses. It allows users to connect to each other either by using cables or wirelessly.
Although other network technologies exist, Ethernet has achieved near-ubiquity since the mid-1990s. Every Ethernet network card has a unique 48-bit serial number called a MAC address, which is stored in ROM carried on the card. Every computer on an Ethernet network must have a card with a unique MAC address. No two cards ever manufactured share the same address. This is accomplished by the Institute of Electrical and Electronics Engineers (IEEE), which is responsible for assigning unique MAC addresses to the vendors of network interface controllers.
Whereas network cards used to be expansion cards that plug into a computer bus, the low cost and ubiquity of the Ethernet standard means that most newer computers have a network interface built into the motherboard. These either have Ethernet capabilities integrated into the motherboard chipset, or implemented via a low cost dedicated Ethernet chip, connected through the PCI (or the newer PCI express bus). A separate network card is not required unless multiple interfaces are needed or some other type of network is used. Newer motherboards may even have dual network (Ethernet) interfaces built-in.
The card implements the electronic circuitry required to communicate using a specific physical layer and data link layer standard such as Ethernet or token ring. This provides a base for a full network protocol stack, allowing communication among small groups of computers on the same LAN and large-scale network communications through routable protocols, such as IP.
There are four techniques used to transfer data, the NIC may use one or more of these techniques.
Polling is where the microprocessor examines the status of the peripheral under program control.;
Programmed I/O is where the microprocessor alerts the designated peripheral by applying its address to the system's address bus.;
Interrupt-driven I/O is where the peripheral alerts the microprocessor that it's ready to transfer data.;
DMA is where the intelligent peripheral assumes control of the system bus to access memory directly. This removes load from the CPU but requires a separate processor on the card.;
A network card typically has a twisted pair, BNC, or AUI socket where the network cable is connected, and a few LEDs to inform the user of whether the network is active, and whether or not there is data being transmitted on it. The Network Cards are typically available in 10/100/1000 Mbit/s(Mbit/s). This means they can support a transfer rate of 10 or 100 or 1000 Megabits per second.
Read more at Wikipedia.org
|
|
